Summary Weight Capture tab

Use this tab to configure controls for capturing and tracking weights of license plates at the summary level.

  1. Click the Summary Weight Capture tab to set controls for capturing and tracking weights for license plates at the summary level.
  2. Specify this information:
    Inbound Summary RF Weight Capture
    Check this field to enable the Summary Weight Capture screen for display to the RF operator during receipt. If this field is unchecked (disabled), the system will calculate the weight information of the receipt using the standard weights configured for this item.
    Note: This flag CANNOT be enabled if the Inbound Catch Weight flag on theWeight/Data tab is active. An item cannot be configured to capture both types of weights.
    Outbound Summary RF Weight Capture
    Check this field to enable the Summary Weight Capture screen for display to the RF operator during picking. If this field is unchecked (disabled), the system will calculate the impact of the weight change by prorating the weights on the license plate. This flag CANNOT be enabled if the Outbound Catch Weight flag on the Weight/Data tab is active. An item cannot be configured to capture both types of weights.
    Display Summary RF Weight Capture for Other Transactions
    Check this to enable the Summary Weight Capture screen for display to the RF operator during normal inventory transactions. This includes Adjustment, Inventory Moves, Replenishment, and Cycle Counts. If this is unchecked (disabled), the system will calculate the impact of the weight change by prorating the weights on the license plate.
    UOM for Summary Weight Capture
    This is used to indicate which Unit of Measure the weights configured on this tab. The system will use these two values (UOM and weight), to calculate the expected weight for transactions on RF.
    Default value: blank.
    Note: It is only required if one of the summary capture flags previously discussed are turned on.
    Catch Gross Weight
    Flag that indicates the RF operator will input the Gross Weight (total of Net weight and Tare weight). If activated, the Summary Weight Capture screen will calculate an expected weight and allow the operator to modify.
    Note: This flag is not editable unless at least one of the summary capture flags are turned on.
    Standard Gross Weight

    The average gross weight of the item based on the unit of measure selected in the UOM for Summary Weight Capture field. If the UOM is set to Each, the system will calculate the expected gross weight for the transaction by multiplying the transaction quantity times this Standard Gross Weight value. If the UOM is set to Case, the system will calculate the expected gross weight for the transaction using the transaction quantity divided by the case quantity and then multiplying by this Standard Gross Weight value.

    Default value: Automatically populated when the item is created based on the Gross Weight defined for the item on the General tab.
    Note: The item configuration requires the Gross Weight to be equal to Net Weight + Tare Weight.
    Catch Net Weight
    Flag that indicates the RF operator will input the Net Weight. If activated, Summary Weight Capture screen will calculate an expected weight and allow the operator to modify.
    Note: This flag is not editable unless at least one of the summary capture flags are turned on.
    Standard Net Weight

    The average net weight of the item based on the unit of measure selected in the UOM for Summary Weight Capture field. If the UOM is set to Each, the system will calculate the expected net weight for the transaction by multiplying the transaction quantity times this Standard Net Weight value. If the UOM is Case, the system will calculate the expected net weight for the transaction using the transaction quantity divided by the case quantity and then multiplying by this Standard Net Weight value.

    Default value: This will be automatically populated when the item is created based on the Net Weight defined for the item on the General tab.
    Note: The item configuration requires the Gross Weight to be equal to Net Weight + Tare Weight.
    Catch Tare Weight
    Flag that indicates the RF operator will input the Tare Weight. If activated, the Summary Weight Capture screen will calculate an expected weight and allow the operator to modify.
    Note: This flag is not editable unless at least one of the summary capture flags are turned on.
    Standard Tare Weight

    This is the average tare weight of the item based on the unit of measure selected in the UOM for Summary Weight Capture field on this screen. If the UOM is Each, the system will calculate the expected tare weight for the transaction by multiplying the transaction quantity times this Standard Tare Weight value. If the UOM is Case, the system will calculate the expected tare weight for the transaction using the transaction quantity divided by the case quantity and then multiplying by this Standard Tare Weight value.

    Default value: This will be automatically populated when the item is created based on the Tare Weight defined for the item on the General tab.
    Note: The item configuration requires the Gross Weight to be equal to Net Weight + Tare Weight.
    Zero Default Weight for RF Picking
    Flag that indicates whether the expected weight information for the pick is to be calculated by the system and displayed to the RF operator, or if the weight is to be displayed to the operator as 0 (zero) to force the weight capture.