Forecast engine error codes

Code	Error Message	Algorithm or Parameter (if applicable)	Description
1	An unknown error has occurred.		This is due to some unidentified error. Contact Infor Support.
2	An internal Java error has occurred.	This is due to some unidentified error. Contact Infor Support.
4	There is no non-zero history. A model cannot be fitted.	We cannot identify a non-zero history point, so a forecast cannot be generated. Review Alerts and history for this item. Consider the Short History parameter.
5	All of the non-zero history is masked. The average event cannot be calculated. No model fit can be performed.	Crostons algorithm. Min Periods for SMP.	The item has been identified as SMP, but all non-zero history is masked, so a forecast cannot be generated. Review Alerts (Missing Forecast) and masks for this item.
6	There is not enough history ({0}) periods) to perform the average event calculation. A model cannot be fitted.	Crostons algorithm. Min Periods for SMP.	The item has been identified as SMP but there are not enough history points, so a forecast cannot be generated. A minimum of 4 history periods are required. Review Alerts (Missing Forecast) and history for this item. Consider the Short History parameter.
7	Forecast vector length ({0}) and the horizon ({1}) do not match.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
8	The list of 53 week periods for the forecast is incorrect.	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
9	History vector has a zero length. The model cannot be initialized.	This is an exception already handled in the engine. The item has no history or all non-zero history is masked. Review history and masks for this item. Consider the Short History parameter.
10	History length ({0}) and mask length ({1}) differ. History could not be setup.	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
11	The list of 53 week periods for the history is incorrect.	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
12	Mask vector length ({0}) is too short.	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
13	History vector has zero length.	This is an exception that is already handled in the engine. The item has no history or all non-zero history is masked. Review history and masks for this item. Consider the Short History parameter. Else, contact Infor support.
14	The seasonal type is incorrect. It must be ADDITIVE or MULTIPLICATIVE.	Seasonal Type	Incorrect parameter value. Review this parameter in the forecast engine configuration.
15	The history length ({0}) is not long enough for seasonal indices to be calculated. No model initialisation can be performed.	Holt-Winters algorithm. Initialization Type and Model Form	The history data is not allowed for Medians initialization for a seasonal model. Consider an alternative algorithm or adjust the initialization type or model form parameters.
16	The two series for the least squares fit are of different lengths (x {0} and y {1}).	Least Squares algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
17	The two series are of zero length.	Least Squares algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
18	The X series in the least squares fit sums to zero.	Least Squares algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
19	The Y series in the least squares fit sums to zero.	Least Squares algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
20	The algorithm chosen ({0}) has not been implemented. No model fit can be performed.	Algorithm	Review the Algorithm in the forecast engine configuration. This exception cannot occur as the algorithm selection is made from a set of supported options. Check if algorithm is configured using an invalid template file.
21	There is no history. No model fit can be performed.		We cannot identify any non-zero history points, so a forecast cannot be generated. Review Alerts and history for this item. Consider the Short History parameter.
22	History length ({0}) and mask length ({1}) differ. No model fit can be performed.	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
23	All of the history is masked. No model fit can be performed."	Masks	All non-zero history is masked, so a forecast cannot be generated. Review Alerts (Missing Forecast) and masks for this item.
24	The period, {0}, is invalid.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
26	The history trend damping factor is out of range ({0}). It must be >0 and <=1.	History Trend Damping Factor	The parameter value is outside of the accepted values. Review this parameter in the parameter value in the forecast engine configuration.
27	P Value ({0}) is invalid in the Normal Quantile Function calculation.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
29	History length {(0)} and forecast length ({1}) differ. No summary statistics can be calculated.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
30	History vector has no length. No summary statistics can be calculated.		This is an exception that is already handled in the engine. The item has no history or all non-zero history is masked. Review history and masks for this item. Consider the Short History parameter. Else, contact Infor support.
31	History length ({0}) and mask length ({1}) differ. No summary statistics can be calculated.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
32	The run type of the model is incorrect ({0}). It must be INITIALMODELFIT.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
33	The run type of the model is incorrect ({0}). It must be INITIALMODELFIT.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
34	Forecast horizon ({0}) has not been set.	Cycle future horizon	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP as the forecast horizon is derived from the cycle period. Contact Infor support.
35	There are no model coefficients set up so no forecast can be created.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
36	Tracking signal type is not valid.	Tracking Type	The parameter value is outside the acceptable range. The value must be one of the followings: NOTRACKING SIMPLETRACKINGSIGNAL BROWNSCUSUMTRACKINGSIGNAL TRIGGSSMOOTHEDTRACKINGSIGNAL AUTOCORRELATIONTRACKINGSIGNAL Review this parameter in the forecast engine configuration.
37	Time period ({0}) is larger than the smoothing coefficient vector size ({1}).		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
38	History length ({0}) used in the moving average technique is shorter than the moving point length ({1}). No model fit can be performed.	Moving Average point value	There are not enough history points to fit the specified moving average length, so a forecast cannot be generated. Review Alerts (Missing Forecast) and history for this item. Consider the Short History parameter or reduce the Moving Average point value.
45	An error has occurred in trying to reconstruct the online forecast vector.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
46	The future change period ({0}) is not valid. No model fit will be returned.		This referred to a disabled feature, for future use, and cannot occur unless there is a configuration issue in SCP. Contact Infor support.
47	Ljung-Box Q Statistic P Value cannot be calculated as the history ({0}) and online forecast ({1}) are of different lengths.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
48	The calculation of the auto correlation coefficient is not possible because the lag value ({0}) is greater than or equal to the data length ({1}).		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
49	There are no model coefficients set up.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
50	Exponential moving average lambda coefficient is invalid. It must be >= 0 and <=1.	Exponentially weighted moving average Lambda	The parameter value is outside the acceptable range. Review this parameter in the forecast engine configuration.
51	The model form is incorrect. It must be CONSTANT, LINEAR or SEASONAL.	Model Form	The parameter value is outside of the accepted range. Review this parameter in the forecast engine configuration.
52	The initialization type is incorrect. It should be NOINITIALISATION, MEDIANS, AVERAGING, DECOMPOSITION, LEASTSQUARE, or BACKCASTING.	Initialization Type	The parameter value is outside of the accepted range. Review this parameter in the forecast engine configuration.
53	There is no historical independent data so no regression can be performed.	Multiple Regression algorithm. Independent variable	The forecast engine is using multiple regression, but no historical values are stored for the independent variable. Review the measure data mapped to the independent variable for this item in the forecast engine or change the Algorithm.
54	There is no forecast independent variable data so no forecasts can be calculated.	Multiple Regression algorithm. Independent variable	The forecast engine is using multiple regression, but no historical values are stored for the independent variable. Review the measure data mapped to the independent variable for this item in the forecast engine or change the Algorithm.
55	There are no historical independent variables so no regression can be performed.	Multiple Regression algorithm. Independent variable	The forecast engine is using multiple regression, but no historical values are stored for the independent variable. Review the measure data mapped to the independent variable for this item in the forecast engine or change the Algorithm.
56	There are no beta coefficients for the multiple regression model fit so no forecasts can be calculated.	Multiple Regression algorithm.	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
57	The three matrices are of incompatible dimensions.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
58	The matrix cannot be symmetric because it is not square.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
59	The number of independent variables does not match the number of beta coefficients.	Multiple Regression algorithm. Regression coefficient	The forecast engine is using multiple regression but there is not a regression coefficient mapped for each independent variable. Review the forecast engine configuration or change the Algorithm.
61	There are duplicate independent variables.	Multiple Regression algorithm. Independent variable	The forecast engine is using multiple regression and two or more independent variables are mapped with the duplicate data. Review the measure data mapped to the independent variables for this item in the forecast engine configuration or change the Algorithm.
62	There is not enough forecast independent variable data so no forecasts can be calculated.	Multiple Regression algorithm. Independent variable	The forecast engine is using multiple regression, but not enough forecast values are stored for any independent variables. Review the measure data mapped to the independent variables for this item in the forecast engine configuration or change the Algorithm.
63	Tracking signal control limit is not valid.	Tracking Control Limit	The parameter value is outside of the accepted range. The value must be one of the following: 0.8, 0.9, 0.95, 0.96, 0.97, 0.98, 0.99. Review this parameter in the forecast engine configuration.
64	The Crostons algorithm cannot be used with events modeling.	Crostons algorithm. Perform Event Modeling. Minimum Periods for SMP	The item has been identified as SMP, however Events data is defined and event modelling is enabled. Review the measure data mapped to the Events in the forecast engine configuration for this item-location. Else, review this parameter to consider if this item must be classified as an SMP, calculated with Crostons.
65	The data is too short to apply differencing.		Not yet implemented. If returned, contact Infor support.
66	The data is too short to apply seasonal differencing.		Not yet implemented. If returned, contact Infor support.
67	There are not enough data points to reasonably calculate the p value.	Not yet implemented. If returned, contact Infor support.
68	There are too many data points to reasonably calculate the p value.		Not yet implemented. If returned, contact Infor support.
69	The time period is invalid.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
70	The history is too short to fit a model.		This is an exception already handled in the engine. The item cannot have enough history observations for the selected algorithm. Review history for this item. Consider the Short History parameter.
71	The algorithm chosen ({0}) has not had parameter optimisation implemented. No model fit can be performed.	Algorithm. Optimize Parameters	The algorithm in the forecast engine configuration is not compatible with Optimize Parameters = True. Consider a different algorithm or set Optimize Parameters = False.
72	The moving average point cannot be zero.	Moving Average point value	The parameter value is outside of the acceptable range. The value must be a positive integer. Review this parameter in the forecast engine configuration.
73	No algorithms were processed for the call to BEST.	Best algorithm	This is an exception already handled in the engine. No valid models are returned by the best fit process. This error cannot occur unless there is a configuration issue in SCP. Contact Infor support.
74	The discount factor vector is null.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
75	There are negative event magnitudes for a call to the forecasting engine using the EVENTSONLY algorithm. This is not presently supported.	Events Only algorithm	Negative event magnitudes are not supported for Events Only algorithm. Review the measure data mapped to the Events profiles for this item in the forecast engine or change the Algorithm.
76	There are both positive and negative event magnitudes for a call to the forecasting engine using an algorithm other than EVENTSONLY. This is not presently supported.	Perform Events Modeling	The forecast engine is set to perform Event modeling but one of the event profiles contains both negative and positive values which is not supported. Review the measure data mapped to the Events profiles for this item in the forecast engine and split the positive and negative values to a different Events measure (profile).
78	The forecasting engine was unable to select an algorithm due to the forecast magnitude test failing for all algorithms.	Best algorithm. Forecast Test Magnitude	No forecast is returned by the Best Fit process for this item as all available models failed the forecast magnitude test. Review Alerts (Forecast Magnitude Error) for affected items. Also, review this parameter in the forecast engine configuration, considering a higher value or disabling the test.
79	There is no non-zero history in the most recent {0} periods.	Recent History	The item failed the recent history test, so no forecast is calculated. Review Alerts (No Recent History) for affected items. Also review the Recent History parameter in the forecast engine configuration, lowering the value or disabling the test, to reduce the number of items raised with this exception.
80	The independent variables are all equal. This is not permitted. Choose another algorithm or change the independent variable.	Multiple Regression algorithm. Independent variable	The forecast engine is using multiple regression and one or more independent variables contains the same value for all periods. Review the measure data mapped to the independent variables for this item in the forecast engine configuration or change the algorithm.
81	History length without masked periods {(0)} and retrospective forecast length ({1}) differ. No retrospective summary statistics can be calculated.	Masks	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Review the measure data mapped to Masks for this item. Else, contact Infor support.
82	It was not possible to fit a model due to a data check failure.		This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
85	The history replacement method provided is incorrect. Please provide a valid method.	History Replacement Algorithm	The specified algorithm in the history replacement engine configuration is not valid. The value must be one of the followings: SIMPLEUSERDEFINED SIMPLEPASTYEAR SIMPLENAIVE SIMPLEMEAN BATS LINEARINTERPOLATION FORECASTOFFSET Review this setting in the engine configuration. This is generally selected from a list of valid entries in the UI. It may have been configured using an invalid template file.
86	The start index for history replacement must be greater than or equal to zero.	History Replacement, Replacement Start Date	The measure value mapped to the Replacement Start Date parameter mappings in the history replacement engine configuration is invalid for this item-location. Review the measure data mapped to Replacement Start Date for this item-location, ensuring the date is within the cycle period history horizon.
87	The end index is less than the start index for history replacement.	History Replacement, Replacement Start Date, Replacement End Date	The measure values mapped to the Replacement Start Date and Replacement End Date parameter mappings in the history replacement engine configuration are invalid for this item-location. Review the corresponding measure values ensuring the start date is prior to the end date and both dates are within the cycle period history horizon.
88	The end index is greater than or equal to the history length for history replacement.	History Replacement. Replacement End Date	The measure value mapped to the Replacement End Date parameter mappings in the history replacement engine configuration are invalid for this item-location. Review the measure data mapped to Replacement Start Date for this item-location, ensuring the end date is within the cycle period history horizon.
89	No history has been provided for this history replacement method.	History Replacement. Input History	We cannot identify the first non-zero history point, so a replacement value cannot be generated. Review the measure data mapped to Input History for this item-location.
90	No forecast offset has been provided for this history replacement method.	History Replacement, Offset Forecasts algorithm, Offset Forecast	The history replacement engine is using Offset Forecasts. However, there is no offset forecast value to use for the replacement calculation.
91	The history length is zero and that is incompatible with the history replacement type.	History Replacement, Replacement Start Date, Input History	There is not enough history prior to the replacement start date, so a replacement value cannot be generated for the defined algorithm. Review the measure data mapped to Input History and Replacement Start Date for this item-location or consider an alternative algorithm (User-defined, Offset Forecasts).
92	The start index for history replacement must be greater than zero when the method is not user defined.	History Replacement, Replacement Start Date	The measure value mapped to the Replacement Start Date parameter mappings in the history replacement engine configuration is not defined or is set to a date within the first period for this item-location. A start date within the first period is not possible for most algorithms. Review the measure data mapped to Replacement Start Date for this item-location or consider the User-Defined Value algorithm.
200	Invalid trend discount factor.	BATS algorithm, Routine Trend Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
201	Invalid seasonal discount factor.	BATS algorithm. Routine Seasonal Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
202	Invalid regression discount factor.	BATS algorithm. Routine Regression Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
203	Invalid variance discount factor.	BATS algorithm. Routine Variance Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
204	Demand and outlier lengths differ.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
205	Demand and missing lengths differ.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
206	Invalid time index for regressor.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
207	Invalid regressor index	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
208	Unable to determine level for multiplicative seasonality.	BATS algorithm. Seasonal Type	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support or modify the value of Seasonal Type to NONE or ADDITIVE.
209	DLM trend component has unknown form.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
210	Regressor index out of range	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
211	Possible DLM dimension error	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
212	DLM maximum model terms is invalid.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
214	Maximum model terms is out of range.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
215	Index out of bounds for regressor.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
216	Time index out of bounds.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
217	The matrix is not square and cannot be resized.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
218	Unable to determine level - no model defined.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
219	No BATS model exists.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
220	Out of bounds period for processed DLMs	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
221	Insufficient values for reference initialisation.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
222	Unable to perform reference initialisation. Regression values produced a singular matrix.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
223	Unhandled monitor signal.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
224	Invalid forecast variance.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
225	Out of bounds period for online processed DLM retrieve.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
226	Out of bounds period for retro processed DLM retrieve.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
227	Out of bounds period for online processed DLM assignment.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
228	Out of bounds period for retro processed DLM assignment.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
229	Prior covariance is singular in Back Filter.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
230	Trend discount factor out of range. Check the database.	BATS algorithm. Routine Trend Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
231	Seasonal discount factor out of range. Check the database.	BATS algorithm. Routine Seasonal Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
232	Variance discount factor out of range. Check the database.	BATS algorithm. Routine Variance Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
233	Regression discount factor out of range. Check the database.	BATS algorithm. Routine Regression Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
234	Intervention trend discount factor out of range. Check the database.	BATS algorithm. Intervention Trend Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, lower than the routine value. Review this parameter in the forecast engine configuration.
235	Intervention seasonal discount factor out of range. Check the database.	BATS algorithm. Intervention Seasonal Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, typically lower than the routine value. Review this parameter in the forecast engine configuration.
236	Intervention variance discount factor out of range. Check the database.	BATS algorithm. Intervention Variance Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, typically lower than the routine value. Review this parameter in the forecast engine configuration.
237	Intervention regression discount factor out of range. Check the database.	BATS algorithm. Intervention Regression Discount	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, typically lower than the routine value. Review this parameter in the forecast engine configuration.
238	Scale shift inflation factor out of range. Check the database.	BATS algorithm. Scale Inflation Factor	The parameter value is outside of the accepted range. The value must be a decimal between 0.001 - 100. Review this parameter in the forecast engine configuration.
239	Scale shift threshold out of range. Check the database.	BATS algorithm. Scale inflation threshold	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
240	Level increase threshold out of range. Check the database.	BATS algorithm. Level inflation threshold	The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1. Review this parameter in the forecast engine configuration.
241	Maximum model terms out of range. Check the database.	BATS algorithm. Maximum Model Terms	The parameter value is outside of the accepted range. The value must be an integer between 1 to 14. Review this parameter in the forecast engine configuration.
242	Harmonic significance level out of range. Check the database.	BATS algorithm. Confidence Limit	The parameter value is outside of the accepted range. The value must be one of the followings: 0, 90, 95, 97.5, 99, 99.5. Review this parameter in the forecast engine configuration.
243	Forecast independent variable length and forecast horizon do not match.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
244	Independent variables are of differing lengths.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.
245	Invalid statistical model.	BATS algorithm	This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP. Contact Infor support.

1

An unknown error has occurred.

This is due to some unidentified error. Contact Infor Support.

2

An internal Java error has occurred.

This is due to some unidentified error. Contact Infor Support.

4

There is no non-zero history. A model cannot be fitted.

We cannot identify a non-zero history point, so a forecast cannot be generated. Review Alerts and history for this item. Consider the Short History parameter.

5

All of the non-zero history is masked. The average event cannot be calculated. No model fit can be performed.

Crostons algorithm. Min Periods for SMP.

The item has been identified as SMP, but all non-zero history is masked, so a forecast cannot be generated.

Review Alerts (Missing Forecast) and masks for this item.

6

There is not enough history ({0}) periods) to perform the average event calculation. A model cannot be fitted.

Crostons algorithm. Min Periods for SMP.

The item has been identified as SMP but there are not enough history points, so a forecast cannot be generated. A minimum of 4 history periods are required.

Review Alerts (Missing Forecast) and history for this item. Consider the Short History parameter.

7

Forecast vector length ({0}) and the horizon ({1}) do not match.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

8

The list of 53 week periods for the forecast is incorrect.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

9

History vector has a zero length. The model cannot be initialized.

This is an exception already handled in the engine. The item has no history or all non-zero history is masked.

Review history and masks for this item. Consider the Short History parameter.

10

History length ({0}) and mask length ({1}) differ. History could not be setup.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

11

The list of 53 week periods for the history is incorrect.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

12

Mask vector length ({0}) is too short.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

13

History vector has zero length.

This is an exception that is already handled in the engine. The item has no history or all non-zero history is masked.

Review history and masks for this item. Consider the Short History parameter. Else, contact Infor support.

14

The seasonal type is incorrect. It must be ADDITIVE or MULTIPLICATIVE.

Seasonal Type

Incorrect parameter value. Review this parameter in the forecast engine configuration.

15

The history length ({0}) is not long enough for seasonal indices to be calculated. No model initialisation can be performed.

Holt-Winters algorithm. Initialization Type and Model Form

The history data is not allowed for Medians initialization for a seasonal model.

Consider an alternative algorithm or adjust the initialization type or model form parameters.

16

The two series for the least squares fit are of different lengths (x {0} and y {1}).

Least Squares algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

17

The two series are of zero length.

Least Squares algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

18

The X series in the least squares fit sums to zero.

Least Squares algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

19

The Y series in the least squares fit sums to zero.

Least Squares algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

20

The algorithm chosen ({0}) has not been implemented. No model fit can be performed.

Algorithm

Review the Algorithm in the forecast engine configuration. This exception cannot occur as the algorithm selection is made from a set of supported options.

Check if algorithm is configured using an invalid template file.

21

There is no history. No model fit can be performed.

We cannot identify any non-zero history points, so a forecast cannot be generated.

Review Alerts and history for this item. Consider the Short History parameter.

22

History length ({0}) and mask length ({1}) differ. No model fit can be performed.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

23

All of the history is masked. No model fit can be performed."

Masks

All non-zero history is masked, so a forecast cannot be generated.

Review Alerts (Missing Forecast) and masks for this item.

24

The period, {0}, is invalid.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

26

The history trend damping factor is out of range ({0}). It must be >0 and <=1.

History Trend Damping Factor

The parameter value is outside of the accepted values.

Review this parameter in the parameter value in the forecast engine configuration.

27

P Value ({0}) is invalid in the Normal Quantile Function calculation.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

29

History length {(0)} and forecast length ({1}) differ. No summary statistics can be calculated.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

30

History vector has no length. No summary statistics can be calculated.

This is an exception that is already handled in the engine. The item has no history or all non-zero history is masked.

Review history and masks for this item. Consider the Short History parameter. Else, contact Infor support.

31

History length ({0}) and mask length ({1}) differ. No summary statistics can be calculated.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

32

The run type of the model is incorrect ({0}). It must be INITIALMODELFIT.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

33

The run type of the model is incorrect ({0}). It must be INITIALMODELFIT.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

34

Forecast horizon ({0}) has not been set.

Cycle future horizon

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP as the forecast horizon is derived from the cycle period.

Contact Infor support.

35

There are no model coefficients set up so no forecast can be created.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

36

Tracking signal type is not valid.

Tracking Type

The parameter value is outside the acceptable range. The value must be one of the followings:

NOTRACKING
SIMPLETRACKINGSIGNAL
BROWNSCUSUMTRACKINGSIGNAL
TRIGGSSMOOTHEDTRACKINGSIGNAL
AUTOCORRELATIONTRACKINGSIGNAL

Review this parameter in the forecast engine configuration.

37

Time period ({0}) is larger than the smoothing coefficient vector size ({1}).

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

38

History length ({0}) used in the moving average technique is shorter than the moving point length ({1}). No model fit can be performed.

Moving Average point value

There are not enough history points to fit the specified moving average length, so a forecast cannot be generated.

Review Alerts (Missing Forecast) and history for this item. Consider the Short History parameter or reduce the Moving Average point value.

45

An error has occurred in trying to reconstruct the online forecast vector.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

46

The future change period ({0}) is not valid. No model fit will be returned.

This referred to a disabled feature, for future use, and cannot occur unless there is a configuration issue in SCP.

Contact Infor support.

47

Ljung-Box Q Statistic P Value cannot be calculated as the history ({0}) and online forecast ({1}) are of different lengths.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

48

The calculation of the auto correlation coefficient is not possible because the lag value ({0}) is greater than or equal to the data length ({1}).

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

49

There are no model coefficients set up.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

50

Exponential moving average lambda coefficient is invalid. It must be >= 0 and <=1.

Exponentially weighted moving average Lambda

The parameter value is outside the acceptable range. Review this parameter in the forecast engine configuration.

51

The model form is incorrect. It must be CONSTANT, LINEAR or SEASONAL.

Model Form

The parameter value is outside of the accepted range. Review this parameter in the forecast engine configuration.

52

The initialization type is incorrect. It should be NOINITIALISATION, MEDIANS, AVERAGING, DECOMPOSITION, LEASTSQUARE, or BACKCASTING.

Initialization Type

The parameter value is outside of the accepted range.

Review this parameter in the forecast engine configuration.

53

There is no historical independent data so no regression can be performed.

Multiple Regression algorithm. Independent variable

The forecast engine is using multiple regression, but no historical values are stored for the independent variable.

Review the measure data mapped to the independent variable for this item in the forecast engine or change the Algorithm.

54

There is no forecast independent variable data so no forecasts can be calculated.

Multiple Regression algorithm. Independent variable

The forecast engine is using multiple regression, but no historical values are stored for the independent variable.

Review the measure data mapped to the independent variable for this item in the forecast engine or change the Algorithm.

55

There are no historical independent variables so no regression can be performed.

Multiple Regression algorithm. Independent variable

The forecast engine is using multiple regression, but no historical values are stored for the independent variable.

Review the measure data mapped to the independent variable for this item in the forecast engine or change the Algorithm.

56

There are no beta coefficients for the multiple regression model fit so no forecasts can be calculated.

Multiple Regression algorithm.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

57

The three matrices are of incompatible dimensions.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

58

The matrix cannot be symmetric because it is not square.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

59

The number of independent variables does not match the number of beta coefficients.

Multiple Regression algorithm.

Regression coefficient

The forecast engine is using multiple regression but there is not a regression coefficient mapped for each independent variable.

Review the forecast engine configuration or change the Algorithm.

61

There are duplicate independent variables.

Multiple Regression algorithm. Independent variable

The forecast engine is using multiple regression and two or more independent variables are mapped with the duplicate data. Review the measure data mapped to the independent variables for this item in the forecast engine configuration or change the Algorithm.

62

There is not enough forecast independent variable data so no forecasts can be calculated.

Multiple Regression algorithm. Independent variable

The forecast engine is using multiple regression, but not enough forecast values are stored for any independent variables.

Review the measure data mapped to the independent variables for this item in the forecast engine configuration or change the Algorithm.

63

Tracking signal control limit is not valid.

Tracking Control Limit

The parameter value is outside of the accepted range. The value must be one of the following:

0.8, 0.9, 0.95, 0.96, 0.97, 0.98, 0.99.

Review this parameter in the forecast engine configuration.

64

The Crostons algorithm cannot be used with events modeling.

Crostons algorithm. Perform Event Modeling. Minimum Periods for SMP

The item has been identified as SMP, however Events data is defined and event modelling is enabled.

Review the measure data mapped to the Events in the forecast engine configuration for this item-location. Else, review this parameter to consider if this item must be classified as an SMP, calculated with Crostons.

65

The data is too short to apply differencing.

Not yet implemented. If returned, contact Infor support.

66

The data is too short to apply seasonal differencing.

Not yet implemented. If returned, contact Infor support.

67

There are not enough data points to reasonably calculate the p value.

Not yet implemented. If returned, contact Infor support.

68

There are too many data points to reasonably calculate the p value.

Not yet implemented. If returned, contact Infor support.

69

The time period is invalid.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

70

The history is too short to fit a model.

This is an exception already handled in the engine. The item cannot have enough history observations for the selected algorithm. Review history for this item.

Consider the Short History parameter.

71

The algorithm chosen ({0}) has not had parameter optimisation implemented. No model fit can be performed.

Algorithm. Optimize Parameters

The algorithm in the forecast engine configuration is not compatible with Optimize Parameters = True.

Consider a different algorithm or set Optimize Parameters = False.

72

The moving average point cannot be zero.

Moving Average point value

The parameter value is outside of the acceptable range. The value must be a positive integer.

Review this parameter in the forecast engine configuration.

73

No algorithms were processed for the call to BEST.

Best algorithm

This is an exception already handled in the engine. No valid models are returned by the best fit process.

This error cannot occur unless there is a configuration issue in SCP. Contact Infor support.

74

The discount factor vector is null.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

75

There are negative event magnitudes for a call to the forecasting engine using the EVENTSONLY algorithm. This is not presently supported.

Events Only algorithm

Negative event magnitudes are not supported for Events Only algorithm.

Review the measure data mapped to the Events profiles for this item in the forecast engine or change the Algorithm.

76

There are both positive and negative event magnitudes for a call to the forecasting engine using an algorithm other than EVENTSONLY.

This is not presently supported.

Perform Events Modeling

The forecast engine is set to perform Event modeling but one of the event profiles contains both negative and positive values which is not supported.

Review the measure data mapped to the Events profiles for this item in the forecast engine and split the positive and negative values to a different Events measure (profile).

78

The forecasting engine was unable to select an algorithm due to the forecast magnitude test failing for all algorithms.

Best algorithm. Forecast Test Magnitude

No forecast is returned by the Best Fit process for this item as all available models failed the forecast magnitude test.

Review Alerts (Forecast Magnitude Error) for affected items. Also, review this parameter in the forecast engine configuration, considering a higher value or disabling the test.

79

There is no non-zero history in the most recent {0} periods.

Recent History

The item failed the recent history test, so no forecast is calculated.

Review Alerts (No Recent History) for affected items. Also review the Recent History parameter in the forecast engine configuration, lowering the value or disabling the test, to reduce the number of items raised with this exception.

80

The independent variables are all equal. This is not permitted. Choose another algorithm or change the independent variable.

Multiple Regression algorithm. Independent variable

The forecast engine is using multiple regression and one or more independent variables contains the same value for all periods.

Review the measure data mapped to the independent variables for this item in the forecast engine configuration or change the algorithm.

81

History length without masked periods {(0)} and retrospective forecast length ({1}) differ. No retrospective summary statistics can be calculated.

Masks

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Review the measure data mapped to Masks for this item. Else, contact Infor support.

82

It was not possible to fit a model due to a data check failure.

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

85

The history replacement method provided is incorrect. Please provide a valid method.

History Replacement Algorithm

The specified algorithm in the history replacement engine configuration is not valid. The value must be one of the followings:

SIMPLEUSERDEFINED
SIMPLEPASTYEAR
SIMPLENAIVE
SIMPLEMEAN
BATS
LINEARINTERPOLATION
FORECASTOFFSET

Review this setting in the engine configuration. This is generally selected from a list of valid entries in the UI. It may have been configured using an invalid template file.

86

The start index for history replacement must be greater than or equal to zero.

History Replacement, Replacement Start Date

The measure value mapped to the Replacement Start Date parameter mappings in the history replacement engine configuration is invalid for this item-location. Review the measure data mapped to Replacement Start Date for this item-location, ensuring the date is within the cycle period history horizon.

87

The end index is less than the start index for history replacement.

History Replacement, Replacement Start Date, Replacement End Date

The measure values mapped to the Replacement Start Date and Replacement End Date parameter mappings in the history replacement engine configuration are invalid for this item-location.

Review the corresponding measure values ensuring the start date is prior to the end date and both dates are within the cycle period history horizon.

88

The end index is greater than or equal to the history length for history replacement.

History Replacement. Replacement End Date

The measure value mapped to the Replacement End Date parameter mappings in the history replacement engine configuration are invalid for this item-location.

Review the measure data mapped to Replacement Start Date for this item-location, ensuring the end date is within the cycle period history horizon.

89

No history has been provided for this history replacement method.

History Replacement. Input History

We cannot identify the first non-zero history point, so a replacement value cannot be generated.

Review the measure data mapped to Input History for this item-location.

90

No forecast offset has been provided for this history replacement method.

History Replacement, Offset Forecasts algorithm, Offset Forecast

The history replacement engine is using Offset Forecasts. However, there is no offset forecast value to use for the replacement calculation.

91

The history length is zero and that is incompatible with the history replacement type.

History Replacement, Replacement Start Date, Input History

There is not enough history prior to the replacement start date, so a replacement value cannot be generated for the defined algorithm.

Review the measure data mapped to Input History and Replacement Start Date for this item-location or consider an alternative algorithm (User-defined, Offset Forecasts).

92

The start index for history replacement must be greater than zero when the method is not user defined.

History Replacement, Replacement Start Date

The measure value mapped to the Replacement Start Date parameter mappings in the history replacement engine configuration is not defined or is set to a date within the first period for this item-location. A start date within the first period is not possible for most algorithms.

Review the measure data mapped to Replacement Start Date for this item-location or consider the User-Defined Value algorithm.

200

Invalid trend discount factor.

BATS algorithm, Routine Trend Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

201

Invalid seasonal discount factor.

BATS algorithm. Routine Seasonal Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

202

Invalid regression discount factor.

BATS algorithm. Routine Regression Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

203

Invalid variance discount factor.

BATS algorithm. Routine Variance Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

204

Demand and outlier lengths differ.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

205

Demand and missing lengths differ.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

206

Invalid time index for regressor.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

207

Invalid regressor index

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

208

Unable to determine level for multiplicative seasonality.

BATS algorithm. Seasonal Type

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support or modify the value of Seasonal Type to NONE or ADDITIVE.

209

DLM trend component has unknown form.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

210

Regressor index out of range

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

211

Possible DLM dimension error

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

212

DLM maximum model terms is invalid.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

214

Maximum model terms is out of range.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

215

Index out of bounds for regressor.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

216

Time index out of bounds.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

217

The matrix is not square and cannot be resized.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

218

Unable to determine level - no model defined.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

219

No BATS model exists.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

220

Out of bounds period for processed DLMs

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

221

Insufficient values for reference initialisation.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

222

Unable to perform reference initialisation. Regression values produced a singular matrix.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

223

Unhandled monitor signal.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

224

Invalid forecast variance.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

225

Out of bounds period for online processed DLM retrieve.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

226

Out of bounds period for retro processed DLM retrieve.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

227

Out of bounds period for online processed DLM assignment.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

228

Out of bounds period for retro processed DLM assignment.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

229

Prior covariance is singular in Back Filter.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

230

Trend discount factor out of range. Check the database.

BATS algorithm. Routine Trend Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

231

Seasonal discount factor out of range. Check the database.

BATS algorithm. Routine Seasonal Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

232

Variance discount factor out of range. Check the database.

BATS algorithm. Routine Variance Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

233

Regression discount factor out of range. Check the database.

BATS algorithm. Routine Regression Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

234

Intervention trend discount factor out of range. Check the database.

BATS algorithm. Intervention Trend Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, lower than the routine value.

Review this parameter in the forecast engine configuration.

235

Intervention seasonal discount factor out of range. Check the database.

BATS algorithm. Intervention Seasonal Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, typically lower than the routine value.

Review this parameter in the forecast engine configuration.

236

Intervention variance discount factor out of range. Check the database.

BATS algorithm. Intervention Variance Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, typically lower than the routine value.

Review this parameter in the forecast engine configuration.

237

Intervention regression discount factor out of range. Check the database.

BATS algorithm. Intervention Regression Discount

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1, typically lower than the routine value.

Review this parameter in the forecast engine configuration.

238

Scale shift inflation factor out of range. Check the database.

BATS algorithm. Scale Inflation Factor

The parameter value is outside of the accepted range. The value must be a decimal between 0.001 - 100.

Review this parameter in the forecast engine configuration.

239

Scale shift threshold out of range. Check the database.

BATS algorithm. Scale inflation threshold

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

240

Level increase threshold out of range. Check the database.

BATS algorithm. Level inflation threshold

The parameter value is outside of the accepted range. The value must be a decimal >0 and <=1.

Review this parameter in the forecast engine configuration.

241

Maximum model terms out of range. Check the database.

BATS algorithm. Maximum Model Terms

The parameter value is outside of the accepted range. The value must be an integer between 1 to 14.

Review this parameter in the forecast engine configuration.

242

Harmonic significance level out of range. Check the database.

BATS algorithm. Confidence Limit

The parameter value is outside of the accepted range. The value must be one of the followings:

0, 90, 95, 97.5, 99, 99.5.

Review this parameter in the forecast engine configuration.

243

Forecast independent variable length and forecast horizon do not match.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

244

Independent variables are of differing lengths.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.

245

Invalid statistical model.

BATS algorithm

This is an exception already handled in the engine and cannot occur unless there is configuration issue in SCP.

Contact Infor support.