qmptc domains

The instrument does not need calibration. No data is entered in the fields related to the calibration.

The instrument is calibrated after a specific time interval. It is selected for calibration on or after the next calibration date.

The instrument is calibrated after n time used.

Indicates that the conformance document is created.

Indicates that the user has specified a document number against a specific document pack.

Indicates that the user approved the conformance document before dispatch of goods.

Indicates that the user has not approved the document.

Indicates that test data lines are created for the specified conformance documents with status Pre-Registered or Pre-Approved.

Indicates that the conformance document number is specified in the test data lines of the inspection order.

Indicates that the document is cancelled.

A number with decimals, for example, 3.145.

An exact whole number as opposed to a number with decimals, for example, 1, 2, or 3.

Values (options) for a characteristic must be defined (for example blue), or red.

The default status of the FAI document.

Infor LN populates this status when a order inspection is linked to the FAI.

Infor LN populates this status when the order inspection is processed and the FAI document is approved.

Infor LN populates this status if the order inspection is partially accepted or rejected.

You can set the status to cancelled when the FAI document is in In Process or Required.

All inventory of each item is combined for inspection.

All inventory of each item/warehouse is combined for inspection.

All inventory of each item/warehouse/warehouse location is combined for inspection.

All inventory of each item/warehouse/warehouse location/lot is combined for inspection.

Generate storage inspection for the individual lots and/or serial numbers per business partner.

You print the instruments that are not blocked.

You print the instruments that are blocked.

You print all the instruments.

The limits are entered as percentages of the norm. You can enter the norm in the Norm field.

The limits are entered as values in the Upper Limit field and the Lower Limit field.

If this option is selected, you can enter the test data by Characteristic. A reference to a particular quality or distinctive mark of an item or an item part/component. For example, diameter, length, weight.

If this option is selected, you can enter the test data by Sample Part. A part drawn from the item to test it.

If this option is selected, you can enter the test data by Sequence. The sequence number of the item on the basis of which characteristics are tested on different samples.

To generate new order-specific inspection data.

To update order-specific inspection data. The update procedure will first delete the existing inspection data and then generate new inspection data from the master data.

The characteristic value is calculated by means of an algorithm, using by the inspection results of variable or fixed characteristics.

he characteristic value is determined once and can be entered in the Fixed Characteristic Value field in the Standard Test Procedure Characteristics (qmptc0115m000) session. LN uses this value to compare to the results entered in the Inspection Order Test Data (qmptc1115m000) session or the Sample Test Data by Serial Number (qmptc1116m000) session.

The characteristic value is measured immediately by means of an instrument. The results are entered in the Inspection Order Test Data (qmptc1115m000) session or the Sample Test Data by Serial Number (qmptc1116m000) session.

You enter data in the Inspection Order Test Data (qmptc1115m000) session or in the Sample Test Data by Serial Number (qmptc1116m000) session.

You report inspection order lines completed in the Complete/Process Order Inspections (qmptc1202m000) session.

You generate inspection order lines in the Inspection Order Lines (qmptc1101m000) session.

You print inspection orders in the Print Inspection Orders (qmptc1400m000) session.

The tested quantity passes the test.

The tested quantity does not pass the test.

Only inspection orders with no originating order specified are considered.

Only inspection orders with no re-inspection order specified are considered.

LN decides whether a value is Pass on one of the following conditions: If you entered Integer/Fraction in the Characteristic Type field, and the Measurement Value field is Between Limits or If you entered Option in the Characteristic Type field, and the Option field is Acceptable

LN decides whether a value is Fail on one of the following conditions: If you entered Integer/Fraction in the Characteristic Type field, and the Measurement Value field is Outside Limits or If you entered Option in the Characteristic Type field, and the Option field is Not Acceptable.

A value in terms of a description is reported after testing, for example, Acceptable or Not Acceptable, Good or Bad.

A numeric value is reported after testing, for example, 40 (cm).

The line is created. This is the default status.

When the entry criteria condition is met.

When the criteria for re-validation is met.

When the entry criteria is invalid. This status can set the status manually.

This type of sampling only takes place in case of mass production and is used to control processing. After a particular interval, a sample is drawn equally large as the sample size. A decision is taken based on the quality of the sample whether to continue the production or to stop and take corrective action. For this test type, data must be entered in the following fields:

• - Frequency Unit
• - Quantity

All items are inspected. The sample size and the order quantity have the same value.

One sample out of the entire order quantity is inspected.

Inspection orders are not updated.

Inspection order with status Free are updated.

Inspection orders with the order status Free and Active are updated. For orders with status Free, only the test data entered is updated.

The limits defined for the characteristic cannot be modified in the standard test procedure.

The limits defined for the characteristic can be modified in the standard test procedure