Processed Job Shop Bill of Material Line (tibom5615m100)

Field Information

Site

The code of the site associated with the processed job shop bill of material (BOM).

Product

The code of the product associated with the processed job shop bill of material.

Source Model

The ID of the source bill of material (BOM) from which the job shop bill of material is received.

Source Revision

The revision of the source bill of material that is received.

Position

The position number of the processed job shop bill of material line.

Item

The code of the material that is used for production.

Replaces Item

The material from the previous BOM revision, which is now a use-up material. If the use-up material exists in inventory, that is used instead of the material specified in the Item field.

Bill of Material

The bill of material associated with the processed job shop bill of material.

Revision

The revision number of the processed job shop bill of material.

Status

The status of the job shop bill of material (BOM) model.

Allowed values

New

Approved

Expired

Quantities

Net Quantity

The net quantity of material required to manufacture the selected product.

Unit

The unit in which the net quantity of the material is expressed.

Net Quantity in BOM Unit

The net quantity of material needed to manufacture the selected product expressed in BOM unit.

Note: This field is displayed if the BOM Units on Material Lines check box is selected in the Product Engineering Parameters (timfc0100m000) session.

BOM Unit

The unit in which the net quantity of the material is expressed.

Note: This field is displayed if the BOM Units on Material Lines check box is selected in the Product Engineering Parameters (timfc0100m000) session.

Scrap Percentage

The expected relative material loss, for example due to faulty components. The gross quantity should be increased to compensate for these material losses.

Scrap Quantity

The quantity of material that will be lost during production. The quantity is a fixed quantity that is independent to the quantity produced. Recording a scrap quantity prevents shortages in production.

Note: This field is displayed if the BOM Units on Material Lines check box is selected in the Product Engineering Parameters (timfc0100m000) session.

Scrap Quantity in BOM Unit

The quantity of the material lost in production that is expressed in BOM unit.

Note: This field is displayed if the BOM Units on Material Lines check box is selected in the Product Engineering Parameters (timfc0100m000) session.

Size Unit

The unit of measurement of Length and Width fields.

Length

The length of the material that is used to calculate the net quantity if the inventory unit is Length or area unit. In case of area unit, this field is used in combination with Width.

Note: The Length, Width, Size Unit and Number of Units fields are applicable apply only if the material has length or an area inventory unit, similar to meter and square meter. The inventory unit is defined in the Item (tcibd0501m100) session.

Width

The length of the material that is used to calculate the net quantity if the inventory unit is Width or area unit. In case of area unit, this field is used in combination with Length.

Note: The Length, Width, Size Unit and Number of Units fields are applicable apply only if the material has length or an area inventory unit, similar to meter and square meter. The inventory unit is defined in the Item (tcibd0501m100) session.

Number of Units

The number of times that the required quantity of the material, specified in the Length and/or Width field, appears in the product.

Percentage Required

Indicates the percentage of raw material required to start the operation.

Note: This field is applicable only if the Infor SCM Scheduler check box is selected in the Implemented Software Components (tccom0100s000) session.

Supply

Operation

Indicates the ID of the operation for which the material is required.

Warehouse

The code of the warehouse from which the production materials are delivered.

Lot Selection

The lot selection of the processed job shop bill of material (BOM).

Allowed values

Any

The goods received or shipped are not subject to specific lot conditions. You can use more than one lot.

Same

You can select any lot for receipt or shipment, but the entire receipt or shipment must have the same lot.

Specific

You can receive or ship only one, specific lot.

Customer Furnished Material

If this check box is selected, the specific material is a customer furnished material.

Contains Customer Furnished Material

If this check box is selected, end-item is an item that is built using one or more customer furnished material.

Inherit Demand Peg

Indicates whether the production order associated with the job shop bill of material can have a demand peg.

Note: This field is applicable only if the Project Pegging check box is selected in the Implemented Software Components (tccom0100s000) session.

Supplied by Subcontractor

If this check box is selected, the specified material is supplied by subcontractor.

Phantom

If this check box is selected, the specified material or component is a phantom.

Miscellaneous

Report Material

Indicates the method in which the material is consumed.

Allowed values

Backflush

This is an automatic calculation based on reported quantities.

Manual

Reporting is done by an employee using the Machine Work List (tisfc4600m000) session.

By Machine

Reporting is done via machine operations instead of per operation.

MES

Reporting is done by the integrated Manufacturing Execution System.

By Machine Group

Reporting is done by machine in the Report Operations Completed (tisfc0130m000) session.

Undefined

This applies to Report Machine Hours on converted orders. Reporting is based on the Labor Hours value.

Not Applicable

No reporting is necessary.

Allow Multiple Items

If this check box is selected, LN can distribute the net quantity of the material that is required over multiple items. For example, the net quantity can be divided over the use-up material and the standard material or over the standard material and one or more alternative materials. If this check box is cleared, LN issues only a single item specified in the job shop bill of material for the production order.

Note: This field is applicable only if the Alternative Materials or the Use Up Material check box is selected in the Implemented Software Components (tccom0100s000) session.

Standard Configuration

If this check box is selected, the job shop bill of material line is part of the standard configuration of the product.

Note: This field is applicable only if the Unit Effectivity check box is selected in the Implemented Software Components (tccom0100s000) session.

Print on Order Document

If this check box is selected, the received job shop bill of material components are printed on the order document.

Specify Material Offset

If this check box is selected, you can specify the lead time offset for the material.

Material Offset

The lead-time offset for the availability of the component in days or hours depending on the selected time unit.

Material Offset Unit

The time unit, days or hours, in which the material offset is defined.

Allowed values

Days

Hours

Text

If this check box is selected, a text related to the processed job shop bill of material line exists.