titrp domains

This field has the Not Applicable value if the Tools Requirement Planning module is not implemented.

The tools are planned in the availability planning until the Run of an operation.

The tools are planned in the availability planning until the Wait of an operation.

The tools are planned in the availability planning until the Move of an operation.

The tools are planned in the availability planning until the Queue (next Operation) of an operation.

This order type represents the planned production orders from Enterprise Planning.

This order type represents the planned INV production order from Warehousing.

This order type represents the actual production order from Manufacturing and from the Job Shop Control (JSC) module.

This order type represents the actual service orders from Service.

This order type represents the manufacturing prompt for Repetitive Manufacturing (RPT).

This type of order represents the actual production order from the Job Shop Control module.

This type of order represents the actual service orders from the Service package.

This type of order represents the actual work orders from the Service package.

This type of order represents the actual production schedules from the Repetitive Manufacturing package.

Tools will be planned in ascending order of the remaining tools life. The tools with the minimum remaining life will be planned first, as an estimated requirement for the production order or the service order.

Tools will be planned in descending order of the remaining tools life. The tools with the maximum remaining life will be planned first, as an estimated requirement for the production order or the service order.

The first available tool will be planned for issue. If the Tool's Life Based On is Not Applicable, the planning method must be set to Not Applicable.

Tools with the least tools life, greater than or equal to the order quantity of the production order or the service order, will be planned for estimated requirements.

The tool is available at the Work/Service Center.

The tool is requested at the Work/Service Center.

When a tool is entered in LN, the tool is assigned the New status.

The status must be Available if the tool is to be allocated to a production order or a service order. A multipiece tool can only be Available if at least one component is assigned to the tool in the Tool Components (titrp0506m000) session. You can only change the status of a multipiece tool to Available if the components have the Allocated status, the In Refurbishing status, or the Available status.

You cannot change the Available status of the tool if the tool has the usage status:

• Requested
• In Use
• Returned

Tools with the Blocked status cannot be planned or issued to a production order or a service order. You can only manually set the status of a tool to Blocked in the Tool Numbers (titrp0102m000) session.

If the tool has the Blocked status, the tool is not considered when:

• Planning new estimated requirements.
• Performing the availability check for tools.

You cannot modify the status of a component of a multipiece from Available to Blocked if a second component with one of the following statuses is assigned to the multipiece tool:

• Available status.
• Allocated status.
• In Refurbishing status.

The Allocated status is assigned to a tool when it is requested by means of the Request and Return Tools (titrp0215m000) session. When the tool is returned by means of the Request and Return Tools (titrp0215m000) session, the status changes to Available.

The In Refurbishing status is assigned to a tool when the tool is requested to be refurbished by means of the Request and Return Tools (titrp0215m000) session. Tools with this status will not be planned for issue to a production order or a service order within the planned period of maintenance.

The tool status changes from In Refurbishing to Available if the tool is returned using the Request and Return Tools (titrp0215m000) session.

The tool's life is a measure of the number of hours it can be used.

The tool's life is a measure of the number of times the tool can be used.

This value is possible if the tool's usage is irrelevant. For example, if a tool can be used a infinite number of times.

The where-used report will be printed for tool types linked to the routings of items in Manufacturing for the specified range of tool types.

The where-used report will be printed for tool types linked to reference activities in Service for the specified range of tool types.

The where-used report will be printed for tool types linked to planned activities in Service for the specified range of tool types.

LN sets the usage status to Requested if:

• The tools are requested or returned by means of the Request and Return Tools (titrp0215m000) session. In other words, a request line for this tool exists.
• The Tool Present check box for the requirement is selected.

LN sets the usage status to Not Applicable if a new estimated tool requirement is added for which the Use in Tool Planning is cleared, or for which the Request / Return Tools check box in the Tool Numbers (titrp0102m000) session is cleared.

LN sets the Unallocated usage status if:

• The estimated tool requirement is added.
• The Request / Return Tools check box in the Tool Numbers (titrp0102m000) session for the requirement is cleared.

LN sets the usage status to Returned if the tools are returned to either the next operation, work center, warehouse, or an order in the Request and Return Tools (titrp0215m000) session.

LN sets the usage status to Requested if:

• The tools are requested by means of the Request and Return Tools (titrp0215m000) session.
• The Tool Present check box in the Tool Request - Lines (titrp0516m000) session for the requirement is selected.