The product in which the component item occurs.
Note
To print the information displayed in this session, use the following sessions:
- Print Where-Used BOM Components (tibom1412m000)
Where-Used BOM Component (tibom1512m000)Use this session to display the manufactured items in which a particular item occurs as a component. This is useful when you want to replace components. To select a component for which you want to know in which items it is included, use the Find Record Button. You can also specify a particular BOM position number. You can tab through each of the component items with the Next Group button, showing their parent manufactured item. Note To print the information displayed in this session use the Print Where-Used BOM Components (tibom1412m000) session.
Manufactured Item The product in which the component item occurs. Note To print the information displayed in this session, use the following sessions:
Site The site ID. Position The component's position number. Sequence Number The sequence number is a subdivision of the position number. Item The component item for which you want to know in which manufactured items it is used. You must already have defined the item in the Item - Production (tiipd0101m000) session. Quantity Operation One of a series of steps in a routing that are carried out successively to produce an item. The following data is collected during a routing operation:
This data is used to compute order lead times, to plan production orders and to calculate standard cost. Warehouse A place for storing goods. For each warehouse, you can enter address data and data relating to its type. Lot Selection This field is applicable for lot-controlled items. The values Any, Same, or Specific regard the special conditions for the delivery of lot items on order lines. The values also determine the way lot numbers are assigned. Quantities Length This field can be used, together with the Width field and number of units, to calculate the net quantity. The net quantity is the Length field multiplied by the number of units and multiplied by the Width field, if applicable. In the Print Production Order Documents (tisfc0408m000) session, you can only print a sawing list if you have entered the Length field for the given component. If you have entered both the Length field and the Width field, you can print a cutting list. Width This field can be used, together with the Length field and number of units, to calculate the net quantity. The net quantity is the Length field multiplied by the number of units and multiplied by the Width field, if applicable. If you have entered both the Length field and the Width field, you can print a cutting list in the Print Production Order Documents (tisfc0408m000) session. Number of Units The number of times that the required quantity of the material, specified in the Length field and/or the Width field, appears in the product. Inventory Unit The inventory unit in which quantities of the main item are expressed. Net Quantity The amount of a component item used in the manufactured item. To calculate this amount, multiply the number of units by the value in the Length field and the value in the Width field. For example, if you specify ten units of a component that is 2 cm long and 3 cm wide, the net quantity is 60 (10*2*3). If the width is not specified, the net quantity is 20. Note If a negative quantity is shown, the production of a manufactured item results in a by-product. This by-product is entered in the bill of material with a negative quantity, which is used to calculate the gross material requirement. Quantity-independent lines If the BOM lines are quantity independent, a zero is displayed in this field. Percentage Required The percentage of raw material that must be available before the operation can be started. Scrap Percentage Recording a scrap factor prevents shortages in production. The scrap factor is expressed as a percentage loss. A scrap factor of 5% means that LN will allocate 5% more of a component for a production order (gross material requirement). Scrap is an extra loss in addition to the loss caused by the yield being less than 100%. If you generate the BOM from an engineering BOM, the scrap factor and scrap quantity values will also be copied. However, these values will only be copied if the sequence number is the only thing changed, for example, wheel 10/1 to wheel 10/2. If there is a new item on the BOM line, for example, wheel to spare wheel, the scrap data will not be copied. In this case, the scrap quantity and scrap factor will be zero (0). Scrap Quantity Unusable material or rejects of intermediate products, for example, because of faulty components, or products lost in cutting or sawing operations. The gross material requirements and/or an operation's input quantity must be increased to account for anticipated scrap. In the BOM, you can define scrap as a percentage of the net material requirements, which is the scrap factor, and as a fixed quantity, which is the scrap quantity. A scrap quantity is mostly used to define the amount of material that is lost every time when you start producing, for example, to test the equipment. For an operation, you can only define the scrap as a fixed quantity. The quantity of material that will be lost during production. The quantity is a fixed quantity that is independent to the quantity produced. Recording a scrap quantity prevents shortages in production. Scrap is an extra loss in addition to the loss caused by the yield being less than 100%. If you generate the BOM from an engineering BOM, the scrap factor and scrap quantity values will also be copied. However, these values will only be copied if the sequence number is the only thing changed, for example, wheel 10/1 to wheel 10/2. If a new item exist on the BOM line, for example, wheel to spare wheel, the scrap data will not be copied, In this case scrap quantity and scrap factor will be 0. Validity Effective Change Order The change order that defines the effective date of the BOM line. Effective Date The first day on which a record or a setting is valid. The effective date often includes the effective time. Expiry Change Order The change order that defines the expiry date of the BOM line. Expiry Date The date the bill of material (BOM) is no longer valid. Standard Configuration If this check box is selected, the BOM line is part of an item’s standard configuration. The costs for the BOM line are included in the standard cost. If the Standard Configuration check box is cleared, the BOM line is not part of an item’s standard configuration. The costs for the BOM line are not included in the standard cost. The Standard Configuration check box in combination with the setting of the Valid check box in the Exceptions (tcuef0105m000) session indicates whether an BOM line is used for a specific effectivity unit.
Note If the BOM line has exceptions attached, but you do not want to use the exceptions, for example, for selling spare parts, or for an end item which is not unit-effective, then you can clear this check box. Exceptions Present If this check box is selected, this BOM line has exceptions linked to it. Exceptions are part of the unit effectivity concept. Properties Phantom If this check box is selected, the component item is defined as a phantom in the Item - Production (tiipd0101m000) session. You can use phantom items to record technical information about the product structure or to carry out standard cost calculations. Note
Performance aspects The setting of this field could affect system performance and database growth. For more information, refer to Phantoms. Use Phantom Inventory If this check box is selected, LN checks if any phantom inventory is available. If the phantom item is available in inventory, and the quantity is sufficient, this inventory is used as component in the production order. If no phantom inventory is available, or if the quantity is insufficient, the inventory is not used. LN treats the component as a normal phantom item, so the phantom is exploded for the total quantity. Note The phantom stock is always ignored during planning. Print on Order Document If this check box is selected, the BOM component is printed on the order document. Users can specify whether or not they want to print a BOM material on the order document. For example, a user can choose not to print the floor stock in the material list. Link with EDM If this check box is selected, the engineering bill of material line was copied to the production bill of material. Exploded by Infor Planning If this check box is selected, the bill of material (BOM) is exploded using Infor Planning.
| |||