Generate Maintenance Plan (tsspc2200m000)

	Generate Maintenance Plan (tsspc2200m000) Use this session to generate maintenance plans for a range of serialized items. Note You can generate maintenance plans for the serialized items only if: The Generate Planned Activities check box is selected in the Serialized Items (tscfg2100m000) session for the serialized items. A maintenance scenario is assigned to the serialized items. The status of the serialized item is set to Active, Working Condition or Defective. The start date for the serialized items is equal to the effective date of the Serialized Items (tscfg2100m000) session. The effective date is the installation time of the serialized item and if it is not filled then it is the delivery time and if the delivery time is also not filled then it is creation time of the serialized item. The serialized item's start value is equal to the planned dependent value that you defined for the serialized item in the Planned Activities (tsspc2100m000) session. Selection Range Use the fields in the Selection Range group box to specify the range of data for which the maintenance plans must be generated. Selection Maintenance Scenarios The option to select the maintenance scenarios. Allowed values Select Maintenance Scenarios Type of Scenario The type of scenarios for which the maintenance plans are generated. Allowed values Select Type of Scenarios Maintenance Scenario The From and To fields define a range of: the maintenance scenario codes. Selection Serialized Items The option to select the serialized items. Allowed values Select Serialized Items Owner The From and To fields define a range of: the sold-to business partners specified for the serialized item. In Use-by Business Partner The From and To fields define a range of: the in use-by business partners. Service Department The From and To fields define a range of: the service departments. Installation Group The From and To fields define a range of: the installation groups. Service Item Group The From and To fields define a range of: the service item groups. Serialized Item Group The From and To fields define a range of: the serialized item groups. Usage Class The From and To fields define a range of: the usage classes Item The From and To fields define a range of: the items. Serial Number The From and To fields define a range of: the serial numbers. Use Horizon If this check box is selected, you can specify the time period during which the maintenance plans are generated. Period The number of time periods for which the maintenance plans are generated. Note This field is enabled only if the Use Horizon check box is selected. Period Unit The unit in which the Period is expressed. Note This field is enabled only if the Use Horizon check box is selected. From Date The planned activities can be generated from this date. Note By default, the current system date is used. You can set this value to a date before the current date only if the Generate Planned Activities in the Past Allowed check box is selected in the Service Planning Parameters (tsspc0100m000) session. To Date The planned activities can be generated up to this date. Note This field is enabled only if the Use Horizon check box is cleared. You must set the field to a date greater than the From Date. If the Use Horizon check box is selected, the value in this field is derived as follows: `To Date = From Date + Horizon Period` Only Generate Maintenance Plan for Active Contract Period If this check box is selected, for each serialized item within the specified range, the following is applicable: Based on the From Date, the application searched for an active contract for the serialized item. If not available, planned activities are not generated. In case an active contract exists and if the To Date is after the contract end date, the To Date is defaulted with the contract end data. Start Maintenance Cycle The options to initiate the maintenance cycle. Allowed values Start Maintenance Cycle Note This field is enabled and applicable only if: The Type of Scenario is set to Time Based Only or Time Based and Usage Based. The maintenance scenario line is of the type Time Based or Time Based Pattern. By default, this field is set to Start Date of Serialized Item. Time Based Activities The setting to generate the maintenance plans for the time based activities. Allowed values Generation Type Usage Based Activities The setting to generate the maintenance plans for the usage based activities. Allowed values Generation Type Simulate If this check box is selected, the generation of the maintenance plans is only simulated and no real planned activities are created. Process Report If this check box is selected, a process report is generated with the updated values when the process execution is successful. Note The application selects and disables this check box if the Simulate check box is selected. Error Report If this check box is selected, an error report is generated with the details of the error when the process execution fails. Information Report If this check box is selected, the plan information report is printed.