An integrated module or package to which an (inspection) order
is related.
Inspection Orders (qmptc1100m000)Use this session to maintain the inspection orders that are generated by default. The session also allows you to create new inspection orders. Tabs The tabs refer to:
Note You can only define and modify inspection orders if the Inspection Status field is set to Free or Active in Order Inspections (qmptc1120m000) session, and if no order lines status is not set to Completed in Inspection Order Lines (qmptc1101m000) session.
Origin An integrated module or package to which an (inspection) order
is related. Origin Order The order number of the order for which inspection is needed. Allowed values Position The position number on the order to which the inspection order
is linked. This can be the position number of the sales order line, purchase
order line, or the position number in the BOM. Operation One of a series of steps in a routing that are carried out
successively to produce an item. The following data is collected during a routing operation:
This data is used to compute order lead times, to plan production orders and to calculate standard cost. Sequence The sequence number of the inspection order on the basis of
which characteristics are tested on different samples. Inspection Displays a list of the inspection order lines generated for a
particular inspection order. These lines correspond to characteristics
maintained for each of the test groups that are linked to the quality
ID. Inspection Displays the sequence of the inspection that is carried
out. Critical Characteristic AQL The acceptable quality level defined for a characteristic
with Defect Type set to Critical in the Standard Test Procedure (qmptc0110m100) session. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Critical Characteristics Accepted Quantity The maximum quantity that can be rejected for a specified
sample of a critical characteristic. For a quantity greater than this value,
the whole sample is rejected. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Critical Characteristic Rejected Quantity The minimum quantity that can be rejected for a specified
sample of a critical characteristic. For a quantity greater than this value,
the whole sample is rejected. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Major Characteristic AQL The acceptable quality level defined for a characteristic
with Defect Type set to Major in the Standard Test Procedure (qmptc0110m100) session. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Major Characteristics Accepted Quantity The maximum quantity that can be rejected for a specified
sample of a major characteristic. For a quantity greater than this value, the
whole sample is rejected. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Major Characteristic Rejected Quantity The minimum quantity that can be rejected for a specified
sample of a major characteristic. For a quantity greater than this value, the
whole sample is rejected. Note Infor LN defaults this value from the Matrix specified in the Sampling Plan (qmptc0670m000) session. Minor Characteristic AQL The acceptable quality level defined for a characteristic
with Defect Type set to Minor in the Standard Test Procedure (qmptc0110m100) session. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Minor Characteristics Accepted Quantity The maximum quantity that can be rejected for a specified
sample of a minor characteristic. For a quantity greater than this value, the
whole sample is rejected. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Minor Characteristic Rejected Quantity The minimum quantity that can be rejected for a specified
sample of a minor characteristic. For a quantity greater than this value, the
whole sample is rejected. Note Infor LN defaults this value based on the data specified in the Matrix tab of the Sampling Plan (qmptc0670m000) session. Acceptable Quality Level Switching The method in which the acceptable quality level switching is done. Allowed values Inspection Order inspection order number. Order Quantity The ordered quantity. Item Test Type Specification of the way in which the samples are taken from
the order quantity. Allowed values Frequency The interval between two samples, expressed in the frequency
unit. Explanation: A new sample of 10 pieces is drawn for every 100 pieces. In this case there will be 11 samples of 10 pieces. Example
Frequency You cannot continue the inspection procedure when your order quantity is less than
the frequency quantity (for example, when your order quantity is 40, and your
frequency quantity is 50). In such a case, no samples can be generated, and you
must decrease the frequency quantity. Percentage The sample size is the total quantity that is to be tested. In
this field, the sample size is expressed as a percentage of either the order
quantity or the frequency (in case you selected Continuous Sampling as the test type). Sample Unit The unit of the sample size. Sample Size The size of the item for which the quality is
tested. Acceptable Quality Level The maximum percentage of a test sample that can be rejected
for the item quantity to be approved. For example, if the specified Acceptable
Quality Level (AQL) is 20%, ERP LN approves the item quantity only if the
rejected quantity is less than or equal to 20%. Text If this check box is selected, a text is present. Standard Test Procedure The code to which data is linked that is necessary to check the
quality requirements of an item. Since one standard test procedure can be used
for a group of products that require the same quality standards and tests, a
standard test procedure can considerably reduce time. Version The version number of the standard test procedure. When you
modify a standard test procedure, LN assigns a new
version number. Test Group The definition of how often you take samples to test an order
quantity, and what the sample size is. Order Date The date on which the inspection order is created. Completion Date The date on which all inspection order lines are completed.
This date is updated automatically in the Complete/Process Order Inspections (qmptc1202m000) session and cannot be
entered manually. Test Quantity The part of the sample quantity that is tested. Example A 5 kg
sample will be tested by testing 1 kg at a time. Description The description or name of the code. Business Partner Note If you enter Purchase in the Origin field, you must enter a buy-from business partner in this field. If you entered Sales in the Origin field, you must enter a sold-to business partner in this field. Skip Lot If this check box is selected, only a part of the lot is to be
inspected. Sampling Rule The sampling rule for the inspection order. Inspection Standard The inspection standard defined for the inspection
order. Inspection Severity The severity level defined for the inspection order. Inspection Level The inspection level at which the inspection must be
conducted. Sampling Plan The sampling plan for the inspection order. Number of Iterations The iterations performed for the sampling plan. Iteration The number of times the iteration has been
performed. Reject Quantity The part of the sample quantity rejected after
testing. Accept Quantity The part of the sample quantity accepted after
testing. E-Item Revision The version or revised version of an engineering item (E-item) or a revision-controlled item.
Several revisions of an E-item can exist. Note Note: LN allows you to define sampling rules and testing combinations for specified E-Item Revision. Description The description or name of the code. Effectivity Unit The code that is linked to an end item for identification, and
which can represent the deviation(s) from the standard end item. You can link
an effectivity unit to manufactured items and purchased items. Note LN allows you to define sampling rules and testing combinations for specified Effectivity Unit. Description The description or name of the code. Team The code of the team to which the employees are assigned. Note Infor LN defaults this value based on the Standard Test Procedure.
| |||||||||